En stock Producto destacado
HC-K 6/12-ESTS
HC-K 6/12-ESTS 1636350 PHOENIX CONTACT Contact insert
$114.79USD
128 en stock
Especificaciones clave
:Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Tipo:B16
Ancho:34 mm
Altura:47.2 mm
Información del proveedor
Productos: 0
Normalmente se envía dentro de 2-3 días hábiles
Calidad garantizada
Envío rápido
Soporte técnico
Especificaciones técnicas
| Parámetro | Valor |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Tipo | B16 |
| Ancho | 34 mm |
| Altura | 47.2 mm |
| Longitud | 84.5 mm |
| Serie | HC-K |
| General | For HEAVYCON ADVANCE and HEAVYCON housing of type B16/B32, axial connection for 2 mm Allen wrench |
| Solicitud | Power/signal |
| Tipo de producto | Contact insert with a fixed no. of positions |
| Nota de montaje | To ensure correct use, installation in housing with IP54 protection or better is required |
| Corriente nominal | 40 A (power contacts) |
| Revisión del artículo | 04 |
| Diámetro de contacto | 4 mm |
| Material de contacto | Cu alloy |
| Numeración de contactos | 1 - 6 (power contacts) |
| Hoja de destornillador | 0.5 x 3.5 mm (control contacts) |
| Par de apriete | 2 Nm ... 2.5 Nm (PE connection) |
| Perfil de conexión | 6+12+PE |
| Grado de contaminación | 3 |
| Dibujo dimensional | |
| Número de puestos | 18 |
| Tensión de sobretensión nominal | 8 kV (power contacts) |
| Categoría de sobretensión | III |
| Tecnología de conexión | Axial screw connection (power contacts) |
| Tipo de material de contacto | turned |
| Número de contactos de potencia | 6 |
| Tensión nominal (III/3) | 690 V |
| Sección transversal del conductor | 2.5 mm² ... 10 mm² (power contacts) |
| Número de contactos de control | 12 |
| Material portador de contactos | PC |
| Ciclos de inserción/retiro | ≥ 500 |
| Sección transversal de conexión AWG | 12 ... 8 (power contacts) |
| Temperatura ambiente (funcionamiento) | -40 °C ... 125 °C |
| Distancia del orificio de perforación, horizontal | 77.5 mm |
| Tensión nominal para contactos de potencia | 230/400 V |
| Clasificación de inflamabilidad según UL 94 | V0 |
| Longitud de pelado del cable individual | 8 mm +1 mm (Power 6 mm² ... 10 mm²) |
| Material de la superficie de contacto, contacto de potencia | Ag |
| Material de la superficie de contacto, contacto de control | Ag |
Descripción del producto
Contact insert, number of poles: 6+12+PE, size: B16, power contacts: 6, control contacts: 12, Male, Axial screw connection, 690 V, 40 A, 2.5 mm² ... 10 mm², application: Power/signal
Características clave
- Calidad de grado industrial
- Cumple con RoHS
- Certificado CE
- Garantía de 1 año
Documentos del producto
Hoja de datos
Especificaciones técnicas y datos de rendimiento
Manual de usuario
Guía de instalación y operación
