En stock Producto destacado
UHLAC1
UHLAC1 HLAC1 HL-AC1 PANASONIC HL-T1 sensor controller, NPN, 12-24VDC
$0.00USD
3192 en stock
Especificaciones clave
Artículo:Specifications
Tipo:NPN output
Peso:Net weight: 140 g approx.
Detalles:Controller (NPN output)
Información del proveedor
PANASONIC
Productos: 4316
Normalmente se envía dentro de 2-3 días hábiles
Calidad garantizada
Envío rápido
Soporte técnico
Especificaciones técnicas
| Parámetro | Valor |
|---|---|
| Artículo | Specifications |
| Tipo | NPN output |
| Peso | Net weight: 140 g approx. |
| Detalles | Controller (NPN output) |
| Producto | Ultra-compact Laser Collimated Beam Sensor |
| Material | Enclosure: Polybutylene terephthalateTransparent cover: Polycarbonate |
| Cable de E/S | 0.09 mm210-core composite cable, 2 m6.562 ftlong |
| Número de pieza | HL-AC1 |
| Restablecer entrada | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Nombre del producto | Ultra-compact Laser Collimated Beam Sensor HL-T1 |
| Entrada de tiempo | 0 V connection: EffectiveOpen: Ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Salida lineal | Current / voltage output switchable (Note)-During current output: 4 to 20 mA/F.S., Maximum load resistance: 300 Ohm-During voltage output: plus or minus 4 V/F.S., Output impedance 100 Ohm(In the monitor focus function, it can also be set at plus or minus 5 V, 0 to 5 V, etc.)(Note) Switching between current and voltage is accomplished by a switch on the bottom of the controller. |
| Funciones principales | ・Measured value display・Setting value, light amount value resolution display・Standard received light setting・Automatic scaling・Scaling・Display reverse・ECO display・Display digits limitation・Sample hold・Peak hold・Bottom hold・Peak to peak hold・Self peak hold・Self bottom hold・Zero reset・Initial reset・ON-delay timer・OFF-delay timer・One-shot timer・Differentiation・Sensitivity selection・Threshold value direct setting・Positioning teaching・2-point teaching・Automatic teaching・Hysteresis width variability・Monitor focus・Non-measuring time setting・(A – B) calculation(Note：The calculation unit is necessary.)・(A + B) calculation(Note：The calculation unit is necessary.)・Mutual interference prevention (Note：The calculation unit is necessary.)・Laser deterioration detection・Key lock・Zero reset memory |
| Número de producto | HL-AC1 |
| Tensión de alimentación | 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less |
| Entrada de láser apagado | 0 V connection: Laser emission haltOpen: Laser emission-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Ciclo de medición | 150 micro s |
| Grado de contaminación | 3 (industrial environment) |
| Entrada de reinicio a cero | 0 V connection: Zero reset operatesOpen: Zero reset ineffective-Applied voltage: 30 V DC or less (leak current: 0.1 mA or less) |
| Consumo actual | 190 mA or less (when connected to the sensor head) |
| Extensión de cable de E/S | Extension up to total 10 m32.808 ftis possible, with 0.09 mm2or more, cable.(Note) If the extension cable is longer than 10 m32.808 ft, then it will not qualify for CE marking. |
| Pantalla subdigital | 5 digit yellow LED display[RUN mode: Either the resolution or laser beam reception amount will be displayed. THR mode: The threshold value will be displayed., Reverse mode: The display orientation will be reversed.] |
| Pantalla digital principal | 5 digit red LED display[RUN mode: Either the measured value (mm) or the hold value will be displayed. Reverse mode: The display orientation will be reversed.] |
| Resistencia de aislamiento | 20 MOhm , or more, with 500 V DC megger between all supply terminals connected together and enclosure |
| Cabezal de sensor aplicable | HL-T1001A/T1001F, HL-T1005A/T1005F, HL-T1010A/T1010F |
| Soportabilidad de tensión | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| Indicadores: Habilitar (ENABLE) | Green LED (lights up during normal operation) |
| Indicadores: Resultados del juicio | HIGH: Orange LED (lights up when measured value > HIGH threshold value)PASS: Green LED (lights up when HIGH threshold value >= measured value >= LOW threshold value)LOW: Yellow LED (lights up when LOW threshold value > measured value) |
| Indicadores: Puesta a cero (ZERO) | Green LED (lights up when the zero reset function is enabled) |
| Frecuencia de muestreo promedio configurable | 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1,024 / 2,048 / 4,096(Note) The judgment output and linear output and linear output response time is calculated by (Measuring cycle) x (Set average sampling rate + 1). |
| Cumplimiento de la directiva de marcado CE | EMC Directive, RoHS Directive |
| Resultados de juicio (ALTO, APROBADO, BAJO) | NPN open-collector transistor-Maximum sink current: 50 mA-Applied voltage: 30 V DC or less (between judgment output and 0 V)-Residual voltage: 1.2 V or less (at 50 mA sink current) |
| Indicadores: emisión láser (LD activado) | Green LED (lights up during laser emission) |
| Resistencia ambiental: Humedad ambiente | 35 to 85 % RH, Storage: 35 to 85 % RH |
| Resistencia ambiental: Resistencia a los golpes | 300 m/s2acceleration (30 G approx.) in X, Y and Z directions three times each |
| Salida lineal: Características de temperatura | plus or minus 0.2 % F.S./℃(Note) These are the temperature characteristics of the linear output when the sensor head is connected. |
| Resistencia ambiental: Temperatura ambiente | 0 to +50 ℃+32 to +122 ℉(No dew condensation allowed), Storage: -25 to +65 ℃-13 to +149 ℉ |
| Resistencia ambiental: Resistencia a la vibración | 10 to 150 Hz frequency, 0.7 mm0.028 indouble amplitude in X, Y and Z directions for 80 min. |
| Salidas de juicio (ALTO, PASA, BAJO): Operación de salida | HIGH: ON when measured value > HIGH threshold valuePASS: ON when HIGH threshold value >= measured value >= LOW threshold valueLOW: ON when LOW threshold value > measured value |
| Salidas de juicio (ALTO, APROBADO, BAJO): Número de salidas | HIGH / PASS / LOW 3 values output |
| Resultados de la evaluación (ALTO, APROBADO, BAJO): Categoría de utilización | DC-12 or DC-13 |
| Salidas de juicio (ALTO, PASA, BAJO): Protección contra cortocircuito | Incorporated |
Descripción del producto
HLT1 Series Controller, 12-24 VDC Power, NPN Digital Output, Selectable Analog Output between 4-20mA and ±4V
Características clave
- Calidad de grado industrial
- Cumple con RoHS
- Certificado CE
- Garantía de 1 año
Documentos del producto
Hoja de datos
Especificaciones técnicas y datos de rendimiento
Manual de usuario
Guía de instalación y operación
